free webinar

Tap into the ES Magazine App!
Get the latest industry news on your smart phone or tablet

CRANE ENVIRONMENTAL - Deaeration: Why & How in Industrial Water Cooling



Figure 2. The effect of partial gas pressure and heating.

Mechanical agitation. The heated water must be mechanically agitated by spraying, cascading over trays, or by atomization to expose maximum surface contact to the scrubbing atmosphere, thus permitting complete release and removal of gases. When water is broken down into fine droplets for thin films, the distance that the gas bubble must travel for release is greatly decreased. Thorough agitation also overcomes tendencies of surface tension and viscosity to retain the gas bubbles and increases the rate of gas diffusion from the liquid to the surrounding atmosphere. The deaerating equipment, therefore, must provide the most efficient mechanical agitation possible to permit meeting modern requirements of gas removal. Since a normal warranty of “not to exceed 0.005 cc per liter of oxygen” means less than 7 lbs in a billion pounds of water, the importance of effective agitation cannot be overstressed.

Complete gas removal. Adequate steam must be passed through the water to scrub out and carry away the gases after release. Extremely low partial gas pressure must be maintained since Henry’s Law states that the amount of gas which will dissolve in a liquid is proportional to the partial gas pressure in the atmosphere contacting the liquid. It is mandatory that the volume of scrubbing steam be high to produce the low partial gas pressure, and it is equally mandatory that these conditions prevail throughout the deaerating section. The effect of partial gas pressure and heating is illustrated in Figure 2.


There are five principle types of deaerators: parallel flow tray, counterflow tray, scrubber spray, atomizing spray, and cold water. All designs employ the cardinal principles of deaeration outlined above and are capable of delivering water with a dissolved oxygen removal to ensure the effluent contains 7 ppb or less.

Tray deaerators. Tray (or spray-tray) units are most widely used for deaerating boiler feedwater in industrial plants and central generating stations. Water is heated to full saturation temperature with minimum pressure drop and minimum vent, thereby ensuring best thermal efficiency. Deaeration is accomplished by spreading the water over multiple layers of trays designed to break the water into thin films and drops to promote intimate contact with the scrubbing steam. Parallel downflow designs provide maximum flexibility for application, and it will handle any combination of condensate and makeup. Counterflow designs provide best economy for plants having low makeup requirements (higher condensate return percentage).

Spray-deaerators. These are widely used in industrial plants where treated water makeup is dominant over condensate returns. The most common spray deaerator features a scrubbing device where steam and water are mixed to provide the contact and agitation necessary for a high level of dissolved oxygen reduction. “Scrubber” deaerators are simple and economical with low maintenance but do not perform well at reduced loads. The “atomizing” variation of the spray deaerator was developed for use in marine vessels to accommodate low load operation and are an option to the scrubber-type designs when high load-turndown capability is needed. Atomizing deaerators use an internal valve that varies the steam injection opening to suit the load where the fixed openings used in scrubber type units do not have this ability. Because the atomizing device has moving parts, it adds to the cost and requires more maintenance effort than the scrubber type design.

Cold water deaerators. Cold water deaerators are used primarily to eliminate corrosive gases from cooling water or water used in food processing, where it would be undesirable to increase the water temperature or risk contamination due to contact with the volatile chemicals present in the usual steam supply.

To replace the addition of steam that is characteristic of the usual tray and spray deaerators, a boiling condition is created in a cold water deaerator by pressure reduction using vacuum-producing equipment. Surface contact with scrubbing vapor and agitation is provided by a column of mass transfer packing in lieu of trays, scrubbers, or atomizing devices.


The benefits of deaeration of boiler feed and process water has become so well recognized that even small plants now ensure longer equipment life and reduced maintenance by employing some type of deaeration.

Deaeration today is an important factor in the successful and economical operation of any modern boiler plant, regardless of its size.  TB
You must login or register in order to post a comment.



Image Galleries

ES Gallery: Snapshots & Systems

Check out highlights from projects featured in our magazine this year!

Engineered Systems Magazine


2015 March

Check out the March issue of ES with the cover story: High-Rise Overhaul, and features: Selecting & Installing Fire And Smoke Dampers To Ensure Code Compliance; Energy Optimization In Existing Buildings; and The Skinny On Reactors For VFDs.
Table Of Contents Subscribe

System Design

Based on your experience and knowledge level, are you currently comfortable designing or maintaining a system incorporating VRF or radiant ceiling panels?
View Results Poll Archive


The Green Energy Management Book

Learn from our experts how to evaluate job opportunities, market your services, sell a Walk-through Survey, target areas for an Energy Audit, calculate energy savings, do retrofit work, and win continuing contracts for retrofit work.

More Products

Clear Seas Research

Clear Seas Research ImageWith access to over one million professionals and more than 60 industry-specific publications,Clear Seas Research offers relevant insights from those who know your industry best. Let us customize a market research solution that exceeds your marketing goals.

Tomorrow's Environment Podcast

This series from longtime columnist and chronic forward-thinker Howard McKew covers a lot of ground -- from retrocommissioning to systems training, on toward checklists for drawings and tips for meeting minutes. Click HERE to be taken to the podcast page!


new Facebook icon Twitter icon YouTube iconLinkedIn icon  Google+